this is really a cool thing!
this is really a cool thing!
Wiring and other assembly started slowly.
wow looking spot on ,i would paint black the panels behind the grills though
MADBOY!!!
what a beauty. put's my 2.9 v6 to shame.
your doing a top job.
I just like more with original look and steelie wheels. Nice car you have still
hi. it's the scoop of oh a camero, a few wee welds to strengthen bonnet and it looked ok
Cheers
Obstacles are those frightful things you see when you take your eyes off your goal.
just seen this, awesome build there.
Thanks for comment.
Little update here.
Firstly, your car is fantastic!
Second, where you live and keep your car is fantastic! That is truly idyllic!
Third, you're only 21!!!
Im so so so jealous!
Keep up the great work! Loving watching this progress
Thanks Start of next month I'll take the engine block to machine shop, then finally some building can begin.
dude thats awesome., the colours are brilliant, love it
Awesome looks really nice any more pics??
btw should handle really well with that rear end set up mine does with a atlas axle and poly bushes all round with 1"lowered springs and that was with 17" rims,Now on 18's
great work keep it up
Paul
Front brakes
Hi! Been a while, here couple of pics.
Looking very nice. I wish I had gotten this far with my car
67 TVR VIXEN V8
like the billet love the project
Something happened again, hope you like it I do
Hi,
Where did you bought the flywheel?
One guy did make it from steel for me
Here is small vid of the car finally running!
Great stuff. Any more pics of the finished engine bay? What boost are you running and any idea of power and torque? What pistons and con rods and where did you get the girdle? What do you expect it to safely rev to?
Sweet
great to hear it running
Do you have mutch left to do it ?
Don't have any pics of finished engine bay, because it isn't finished yet Camshaft gear is under modification (making it adjustable), gearbox is out now because clutch didn't work with that mustangs original system. Now intend to use mondeo v6 clutch cylinder with release bearing on it. Pistons are ross custom order, con rods eagle h-profile. Girdle made from my own dimensions by Tommi's Billet here in finland.
Slowly getting there. Next month to the dyno.
http://sultzi.kuvat.fi/kuvat/Videoita/ couple vids.
Did some calculations for speeds in each gear etc. here is a pic.
http://sultzi.kuvat.fi/kuvat/Ford%20...%20T5.jpg/full
mmmmm. love it
Finally got this thing outside the garage and needed a little tidying, all that dust almost over a year been there. Little water and there it was, nice and clean. Tried to do somekind of adjusting too.. still long way to go. One pic for your!
looks the nuts i want a 2 door mk3
Made this little vid to show the project phases.. http://sultzi.kuvat.fi/kuvat/Videoita/Cortinapart1.wmv
love it think a mk3 is my next car
This will be nice when done. Keep up the good work mate
Very nice work!
Ford Escort Mk1 - Ford Escort Mk2 - BMW 325 touring
Looks great
Obstacles are those frightful things you see when you take your eyes off your goal.
Some updates on my mind now.
Brake master cylinder will be wilwood or land rover 25mm.
Also planning to change this to use E85 fuel. So some updates needed to injectors, adding another fuel pump (044) and some updates to fuel lines.
Really liked that main cap ladder. NIce touch. And a very cool project all together! I love the factory look!!
After winter, second start attempt.. http://sultzi.kuvat.fi/kuvat/Videoita/Start2.wmv
Got new radiator, hopefully it little bit helps with the water temps.. Still need to find out what I will use as a fan, need to check the clearance.
Hi, Great job!
I see you have a whiteline Ø24mm Anti roll bar, What do you think of it?
I plane to put one on my Taunus Tc1
Don't Scrap it, Restore it !
Hi! Sorry for taking so long time to answer Haven't driven this yet, so don't know anything about it.
Bookmarks